Model of optimal design of logistics network for remanufacturing of waste products

doi:10.3778/j.issn.1002-8331.2010.26.007

Computer Engineering and Applications ›› 2010, Vol. 46 ›› Issue (26): 22-24.DOI: 10.3778/j.issn.1002-8331.2010.26.007

• 博士论坛 • Previous Articles Next Articles

Model of optimal design of logistics network for remanufacturing of waste products

WU Xing-hua¹，WANG Xu²，LIN Yun¹

1.School of Mechanical Engineering，Chongqing University，Chongqing 400030，China
2.School of Trade and Public Administration，Chongqing University，Chongqing 400030，China

Received:2010-05-18 Revised:2010-07-09 Online:2010-09-11 Published:2010-09-11
Contact: WU Xing-hua

废旧产品回收再制造物流网络的优化设计模型

伍星华¹，王旭²，林云¹

1.重庆大学机械工程学院，重庆 400030
2.重庆大学贸易与行政学院，重庆 400030

通讯作者: 伍星华

Abstract

Abstract: In order to get the minimal total operating cost and the minimal influence to the environment，this paper developes a three-layer optimal design model of reverse logistics composed of handling factory，recycling center and consumption areas，and then ascertains the location and amount of each facilities in the logistics network，and the logistics distribution of each route in the network.Finally an example is given to illustrate the effectiveness of the model.

Key words: logistics network, product remanufacturing, optimal design

摘要： 以总运作成本最小和对环境的影响最小为目标，建立了一个包含再制造工厂、回收中心和消费区域的三层逆向物流网络优化设计模型。并确定了物流网络中各种设施的位置和数量，以及由此构成的各条物流路径上的物流量分配。通过算例验证了模型的有效性。

关键词: 物流网络, 产品再制造, 优化设计

CLC Number:

TH16
F252

WU Xing-hua¹，WANG Xu²，LIN Yun¹. Model of optimal design of logistics network for remanufacturing of waste products[J]. Computer Engineering and Applications, 2010, 46(26): 22-24.

伍星华¹，王旭²，林云¹. 废旧产品回收再制造物流网络的优化设计模型[J]. 计算机工程与应用, 2010, 46(26): 22-24.

[1]	HUO Qingqing, GUO Jianquan. Fuzzy Optimization of 3C Product Sustainable Closed-Loop Logistics Network Under TBL Theory [J]. Computer Engineering and Applications, 2020, 56(19): 237-243.
[2]	YANG Xiaohua, GUO Jianquan. Fuzzy Programming of Closed-Loop Logistics Network for Fresh Products under New Retail Model [J]. Computer Engineering and Applications, 2019, 55(2): 198-205.
[3]	HUANG Yingyi1, LIU Wenqi2. Survivability analysis of logistics network based on cascading failure [J]. Computer Engineering and Applications, 2015, 51(21): 12-17.
[4]	FU Jiangyue, CHEN Gang. Urban logistics network evolution model and algorithm [J]. Computer Engineering and Applications, 2015, 51(15): 17-21.
[5]	JIANG Kehui. Hybrid ABC algorithm with Taguchi method for optimal designing of vehicle component [J]. Computer Engineering and Applications, 2014, 50(1): 246-250.
[6]	GAN Mi, CHEN Si. Regional logistics network design optimal models with consideration of roadway expansion [J]. Computer Engineering and Applications, 2013, 49(4): 26-30.
[7]	LI Lihua, FU Zhuo, ZHOU Heping. Model and algorithm for discrete logistics facility location problem under interval uncertainty demand [J]. Computer Engineering and Applications, 2012, 48(8): 12-15.
[8]	WANG Jia1，2, FU Zhuo1. Research on design and optimum-method of double-layer urban transit network [J]. Computer Engineering and Applications, 2012, 48(36): 1-8.
[9]	WANG Zhenfeng1, CUI Yan1, WANG Liang1, XIE Min2. Optimization for remanufacturing closed-loop logistics network under uncertain environment [J]. Computer Engineering and Applications, 2012, 48(36): 221-226.
[10]	XU Yi. Searching optimal route of mobile agents in logistics network of distribution [J]. Computer Engineering and Applications, 2011, 47(8): 7-10.
[11]	WU Xinghua¹，WANG Xu². Optimal design of hybrid remanufacturing logistics network with multi-objective and multi-period [J]. Computer Engineering and Applications, 2011, 47(2): 21-25.
[12]	WU Xing-hua¹，WANG Xu²，LIN Yun¹. Method of optimal design for integrated manufacturing/remanufacturing logistics network with multi-period under uncertainty [J]. Computer Engineering and Applications, 2010, 46(15): 201-204.
[13]	WANG Jin-hua¹,YIN Ze-yong². Solving constrained discrete optimization problem with Particle Swarm Optimizer [J]. Computer Engineering and Applications, 2008, 44(3): 242-244.

Model of optimal design of logistics network for remanufacturing of waste products

废旧产品回收再制造物流网络的优化设计模型

PDF

Knowledge

Abstract

Cite this article

share this article

References

Related Articles 13

Recommended Articles

Metrics